Designed for ease of use and simplicity. Immersion is easy! You get one enclosure, a dry cooler and 10 meters of tubing. The setup is quick and does not require any special skills or professional knowledge.
The enclosure should be placed inside of your workshop / garage or facility, and the dry cooler – outside, so it has access to fresh air. We use a large 24-30kW rated dry cooler with dual fans and temperature controller. With regards to the enclosure, you need to take into account that it will be quite heavy when filled with hardware and heat transfer fluid, so it should be placed on the ground.
We sell those systems either with or without 150L of Heat Transfer fluid. Miners should be placed tightly in Immersion Mining Enclosure, gaps between the miners avoided, empty spaces filled with containers, so the fluid will be forced to go through the miners or GPU cards and not around.

The whole setup takes just connecting two components with tubing, filling the enclosure with fluid, so it goes over the dividing chamber and starts the system. Fans on dry coolers will start when the fluid temperature goes over 40C/104F. The miners should be placed vertically inside the enclosure and fan emulators or custom firmware should be used. That’s it! We will support you on setup and provide video manuals on connecting and starting the system.

The same Immersion Enclosure but delivered with hydraulic fittings, a brazed plate heat exchanger and an energy-efficient pump system, which is almost. If you have facility (home, office, workshop) heating / cooling loop, you can connect our enclosure and reuse the heat from miners. Providing continuous 40-50C /104-122F to supply home installation in cold season.
An ideal solution for colder regions to supply heat to radiators, pools, jacuzzi or floor heating. Still, for hot season you can purchase a drycooler which will extract excess heat. The most flexible system you can get and install.

Ideally connected by local home installations / heating contractor, but it may be also configured by any DIY type person with 1 inch connectors from our plate heat exchanger to home buffer tank.

A dual loop system is an ideal solution for colder regions to supply heat to radiators, pools, jacuzzi or floor heating. Still, for hot season you can purchase a dry cooler, which will extract excess heat. The dry-cooler can be connected to a home water loop using own auxiliary low-power pump or without it, using just facility flow. The most flexible system you can get and install.

Ideally connected by local home installations / heating contractor, but it may be also configured by any DIY type person with 1 inch connectors from our plate heat exchanger to home buffer tank.

Our rack system is based on Dual loop Universal Immersion Mining Enclosures with custom aluminum frame and table which allows middle enclosures to be slide out from the rack for maintenance. Originally with 3 enclosures but might be stacked to 4 enclosures. This system may be delivered with two types of heat rejection: single enclosure – single loop with dry cooler, or all enclosures connected to facility loop. We recommend the second solution which allows for greater flexibility and scalability.

In scale-up scenario one rack with 3 or more dual loop enclosures connected in series. Each enclosure has own brazed plate heat exchanger and low power, energy-efficient pump. Heat transfer fluid circulates only in enclosures. On the other side, we would use a typical water/glycol heating loop that may reuse the heat for facility purposes or reject the heat to a larger 50-70-100kW dry cooler. Both solutions provide unparalleled density and scalability.

We suggest that such a rack system or dry cooler should be installed by a local contractor which specializes in heating/cooling systems.

Rack system transfers from 50 to 70kW of heat so it requires larger heat rejection device. We suggest dry cooler as 50-60C fluid can be easily and cost-effectively extracted to air without air conditioning, chillers and water towers. The 50-100kW range dry-cooler will be connected to the home or facility loop using own auxiliary low-power pump.

Dry coolers are flexible and easy to size and may be upgraded to any heat load by adding more modules in series. They will use convection for most of the time and are simple to operate.  When properly sized for the local climate, the fans on a dry cooler should only be operated for no more than 20% of the time and only during the hottest time of day. They also require very low maintenance, so they do have lowest operation cost from any other heat rejection methods.

Ideally connected by local home installations / heating contractor which can help you to size and maintain your installation in the long term.